The Raspberry Pi photo frame is a perfect setup for anyone who wants to display photos of their loved ones, memories or anything else might want to display.
This photo frame is a pretty straightforward project and shouldn’t take you too long to set up. You will need the full version of Raspbian installed as we make use of the graphical user interface (GUI).
I pretty much only cover the software side of things in this tutorial there are some pretty cool frame designs out there if you want to extend this further.
The digital photo frame we make is very basic and can be kept completely offline. Connecting to services such as Google Drive and Flickr will require a lot more work.
The equipment that you will need for this digital photo frame is listed below.
SD Card or Micro SD Card if you’re using a Raspberry Pi 2, 3 or B+ (8 GB+ Recommended)
Ethernet Cord or Wifi dongle
External Hard drive or USB Drive
Touch Screen or LCD screen
Raspberry Pi Case
If you want to see a video on how to do this tutorial, then be sure to check out the one below.
I go through everything you need to know about getting this project working.
Can’t see the video? Please support us by disabling your adblocker.
For this project, I am just using the official Raspberry Pi touchscreen that I purchased earlier this year. However, you can use pretty much any screen that you can get your hands on. Just make sure you can hook it up to the Pi either over the DSI port, HDMI port or using a custom HAT.
If you’re looking for some 3D printable frames for either the official touch screen or just a spare screen you have, then Thingiverse has some pretty cool designs. You can find them over at Thingiverse.com.
Setting Up the Raspberry Pi Photo Frame Software
To get this all setup correctly we are going to need to do a bit of setup on the software side of things.
Firstly, we want to prevent the screen from going blank. It is a power saving setting on the Pi.
1. To turn off screen blanking open up the lightdm.conf file.
sudo nano /etc/lightdm/lightdm.conf
2. Now in here add the following line anywhere beneath the [SeatsDefaults] line.
xserver-command=X -s 0 –dpms
3. Save & exit by pressing ctrl+x and then y.
4. Now reboot the Pi, and the screen should no longer switch off after 10 minutes of inactivity. To reboot simply run the following:
If you want to be able to drag and drop your images onto the Pi, you may want to look at setting up a network attached storage. Will allow you to set up a folder that is available on your local network. If you’re in doing such a thing, then my guide on a Raspberry Pi Samba server will take you through all the necessary steps.
I also highly recommend that you setup SSH so you will have remote access when the slideshow is in action. There is no easy way to exit the slideshow unless you turn the device on and off and don’t have it automatically starting.
To set up our slideshow, we’re going to use the feh package. Feh is image viewer and cataloguer. It is a fast image viewer that doesn’t get bogged down with huge GUI dependencies. I chose this as it was the most lightweight package that worked without any huge complications.
1. To install the package, use the following line:
sudo apt-get install feh
2. Now to test that it works enter the following line. Replace
/media/NASHDD1/test with the directory that contains all your image.
DISPLAY=:0.0 XAUTHORITY=/home/pi/.Xauthority /usr/bin/feh --quiet --preload --randomize --full-screen --reload 60 -Y --slideshow-delay 15.0 /media/NASHDD1/test
3. Now we can use short tags to make this command a lot shorter. You can read more about all the flags you can use over at the feh manual page.
DISPLAY=:0.0 XAUTHORITY=/home/pi/.Xauthority /usr/bin/feh -q -p -Z -F -R 60 -Y -D 15.0 /media/NASHDD1/test
4. Now as you will notice this locks up the command line bar. To fix this, add the & after the command and the script/process will launch in the background.
5. So now let’s store this in a simple script file. This way you can add or change it later. To make the file enter the following command:
sudo nano /home/pi/start-picture-frame.sh
6. In here enter the following lines:
#!/bin/bash DISPLAY=:0.0 XAUTHORITY=/home/pi/.Xauthority /usr/bin/feh -q -p -Z -F -R 60 -Y -D 15.0 /media/NASHDD1/test
7. Now that’s done you can test it by running the following command(Ctrl+X):
8. Finally, let’s have it start at boot. Now it is important that you have SSH enabled so you can access the Pi remotely as you will lose access to the GUI/Screen. So make sure you have done this before setting it to launch at boot up.
9. To do this open up the rc.local file by entering the following command.
sudo nano /etc/rc.local
10. Add the following before the exit 0 line in this folder.
sleep 10 bash /home/pi/start-picture-frame.sh &
11. If you ever need to kill the process as you may want to be able to access the desktop, simply enter the following line.
sudo pkill feh
You should now have your very own slideshow of pictures going. If you end up with any troubles, then double check all the steps and look for any errors. If you’re still having trouble, then be sure to seek help on our forums.
I hope you have been able to get your Raspberry Pi photo frame working correctly. If you have any trouble or have an extension that you would like to share, then be sure to drop a comment on the forum. As always if you like my stuff be sure to follow Pi My Life Up on any major social network.